Keyword: Acceptance inspection
British Standards Institute, BSI



Go to All Keywords 		BSI Standards
picture picture picture picture picture picture
BS 182:1972
Specification for galvanized line-wire for telephone and telegraph purposes
0 580 06959 1
Summary: Manufacture, diameter, mass, mechanical and electrical testing and quality of line-wire between 1.52 mm and 6.07 mm nominal diameter. Appendix on alternative method of acceptance testing, based on inspection by attributes.
Keywords: Wires, Electric wires, Telephone lines, Telegraph lines, Steels, Galvanizing, Packaging, Coils, Dimensions, Mass, Diameter, Breaking load, Linear electrical resistance, Acceptance inspection
BS 2969:1980
Specification for high-tensile steel chains (round link) for chain conveyors and coal ploughs
0 580 11386 8
Summary: Calibrated chains having links 14 mm to 30 mm diameter, three grades (B, C and D). Dimensions, material, test requirements, marking, inspection, test certificate (not for lifting purposes).
Keywords: Mining equipment, Mineral extraction equipment, Coal mining, Chains, Conveyor chains, Dimensions, Link chains, Calibrated chains, Dimensional tolerances, Steels, High-tensile steels, Mass, Marking, Mechanical testing, Tensile testing, Elongation, Elongation at fracture, Breaking load, Anchorages, Fatigue testing, Acceptance (approval), Colour codes, Bend testing, Acceptance inspection, Statistical methods of analysis, Acceptance (approval), Test specimens, Testing conditions, Chain pitch, Grades (quality), Impact testing, Statistical quality control, Graphical methods
ISO 610-1979
Specification for high-tensile steel chains (round link) for chain conveyors and coal ploughs
0 580 11386 8
Summary: Calibrated chains having links 14 mm to 30 mm diameter, three grades (B, C and D). Dimensions, material, test requirements, marking, inspection, test certificate (not for lifting purposes).
Keywords: Mining equipment, Mineral extraction equipment, Coal mining, Chains, Conveyor chains, Dimensions, Link chains, Calibrated chains, Dimensional tolerances, Steels, High-tensile steels, Mass, Marking, Mechanical testing, Tensile testing, Elongation, Elongation at fracture, Breaking load, Anchorages, Fatigue testing, Acceptance (approval), Colour codes, Bend testing, Acceptance inspection, Statistical methods of analysis, Acceptance (approval), Test specimens, Testing conditions, Chain pitch, Grades (quality), Impact testing, Statistical quality control, Graphical methods
BS 2X 27:1991
Specification for cellulose finishing scheme for aerospace purposes
0 580 19499 X
Summary: Requirements for materials and performance for application to metallic surfaces.
Keywords: Finishes, Organic coatings, Non-metallic coatings, Coatings, Cellulose derivatives, Cellulose, Life (durability), Performance, Drying, Time, Marking, Specimen preparation, Flexibility, Scratch tests, Visual inspection (testing), Acceptance inspection, Type approval, Aircraft components, Space technology components, Environmental testing, Testing conditions
BS 3135:1989
Specification for gas turbine acceptance test
0 580 17850 1
Summary: Standard procedures and rules for the conduct and reporting of acceptance tests for the performance of gas turbines.
Keywords: Gas turbines, Turbines, Acceptance (approval), Approval testing, Performance testing, Testing conditions, Power measurement, Flow measurement, Temperature measurement, Pressure measurement (fluids), Thermal efficiency, Energy consumption, Reports, Accuracy, Formulae (mathematics), Acceptance inspection
ISO 2314:1989
Specification for gas turbine acceptance test
0 580 17850 1
Summary: Standard procedures and rules for the conduct and reporting of acceptance tests for the performance of gas turbines.
Keywords: Gas turbines, Turbines, Acceptance (approval), Approval testing, Performance testing, Testing conditions, Power measurement, Flow measurement, Temperature measurement, Pressure measurement (fluids), Thermal efficiency, Energy consumption, Reports, Accuracy, Formulae (mathematics), Acceptance inspection
BS 3892-2:1996
Pulverized-fuel ash. Specification for pulverized-fuel ash to be used as a Type I addition
0 580 26444 0
Summary: Specifies physical and chemical properties, sampling, testing and marking for ash to be used as an inert (Type I) addition.
Keywords: Fly ash, Ashes, Concretes, Cements, Grades (quality), Chemical composition, Compositional tolerances, Sulfur trioxide, Moisture, Fineness, Samples, Marking, Colour, Safety measures, Occupational safety, Acceptance inspection
BS 4027:1996
Specification for sulfate-resisting Portland cement
0 580 25324 4
Summary: Requirements for composition, strength, physical and chemical properties of three strength classes.
Keywords: Portland cement, Sulphate-resisting cement, Cements, Composition, Chemical composition, Grades (quality), Compressive strength, Setting, Time, Expansion (deformation), Marking, Safety measures, Acceptance inspection, Storage, Performance
BS 4087:1989
Specification for copper-covered steel wire for telephone and telegraph purposes
0 580 17096 9
Summary: Mechanical and electrical properties of copper-covered steel wire with two grades of conductivity and three of tensile strength together with size tolerances for a range of wire sizes. Metric units.
Keywords: Wires, Electric wires, Steels, Coated materials, Copper, Metal coatings, Telephone equipment, Telegraph equipment, Diameter, Dimensional tolerances, Thickness, Electrical resistance, Electrical resistivity, Stain tests, Visual inspection (testing), Packaging, Marking, Weight (mass), Breaking load, Grades (quality), Acceptance inspection, Tensile strength, Telephone lines, Telegraph lines
BS 4783-1:1988
Storage, transportation and maintenance of media for use in data processing and information storage. Recommendations for disk packs, storage modules and disk cartridges
0 580 16172 2
Summary: Includes a guide to fault identification, to reduce the chance of damage and to give data security over archival periods and in normal use.
Keywords: Magnetic disks, Data media, Data processing, Storage, Materials handling, Transportation, Maintenance, Reconditioning, Inspection, Cleaning, Error detection, Environment (working), Records (documents), Labels, Acclimatization, Modules, Acceptance inspection, Performance
BS 4A 100:2003
Specification for general requirements for bolts and free running nuts of tensile strength not exceeding 1249 MPa
978 0 580 63694 3
Keywords: Bolts, Nuts, Aircraft components, Air transport engineering, Space technology components, External-thread fasteners, Internal-thread fasteners, Threaded fasteners, Threaded components, Fasteners, Threads, Marking, Inspection, Acceptance inspection, Statistical quality control, Quality assurance, Dimensional tolerances, Defects, Surface defects, Metallography, Macroscopic examination, Forgings, Heat treatment, Hardness, Tensile testing, Unified screw threads, Steels, Aluminium alloys, Pan-head fasteners, Hexagonal-head fasteners
BS 5306-6.1:1988
Fire extinguishing installations and equipment on premises. Foam systems. Specification for low expansion foam systems
0 580 16264 8
Summary: Design, installation and maintenance of fixed and semi-fixed systems for use on identified hazards in buildings, industrial plant and storage facilities. Specifies application rates for hydrocarbon and foam destructive liquids.
Keywords: Fire extinguishers (built-in), Fire extinguishers, Firefighting equipment, Foams, Portable, Transportable, Fire safety in buildings, Fire safety, Expansion (deformation), Inspection, Acceptance inspection, Design, Water supply (buildings), Marking, Concentrates, Concentration (chemical), Storage, Pipework systems, Flow rates, Hydrants, Sprayers, Classification systems, Flow measurement, Test equipment, Signs
BS 5952:1980
Specification for muscovite mica components for electronic equipment
0 580 11549 6
Summary: Gives minimum technical requirements, test methods and acceptance conditions for stamped components of diameter up to, and including, 40 mm.
Keywords: Muscovite, Mica, Solid electrical insulating materials, Electrical insulating materials, Size classification, Electronic equipment and components, Thickness, Dimensional tolerances, Sampling methods, Acceptance inspection, Holes, Dimensions, Packaging, Marking
BS 5998:1983
Specification for quality levels for steel valve castings
0 580 13380 X
Summary: Requirements for the inspection, identification and quality levels of steel castings for the pressure containing components of valves. Specifies the integrity of the pressure containing components by conformance to specific quality requirements, appropriate records and casting identification.
Keywords: Steels, Valves, Valve components, Valve bodies, Castings, Grades (quality), Quality control, Acceptance (approval), Acceptance inspection, Inspection, Butt joints, Welded joints
BS 6000-1:2005
Guide to the selection and usage of acceptance sampling systems for inspection of discrete items in lots. General guide to acceptance sampling
0 580 46484 9
Keywords: Inspection, Sampling methods, Acceptance inspection, Statistical quality control, Quality assurance, Quality control, Quality assurance systems, Sampling tables, Inspection by attributes, Inspection by variables
BS 6000-2:2005
Guide to the selection and usage of acceptance sampling systems for inspection of discrete items in lots. Guide to sampling by attributes
0 580 46485 7
Keywords: Inspection, Sampling methods, Acceptance inspection, Statistical quality control, Quality assurance, Quality control, Quality assurance systems, Sampling tables, Inspection by attributes
BS 6000-3:2005
Guide to the selection and usage of acceptance sampling systems for inspection of discrete items in lots. Guide to sampling by variables
0 580 46417 2
Keywords: Inspection, Sampling methods, Acceptance inspection, Statistical quality control, Quality assurance, Quality control, Quality assurance systems, Sampling tables, Inspection by variables
BS 6001-0:2006
Sampling procedures for inspection by attributes. Introduction to the BS 6001 (ISO 2859) series of standards for sampling for inspection by attributes
0 580 49315 6
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Inspection, Sampling tables, Statistical quality control, Quality control, Quality assurance systems, Quality assurance
BS 6001-1:1999
Sampling procedures for inspection by attributes. Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
0 580 35934 4
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Sequential sampling, Sampling tables, Statistical quality control, Inspection, Quality control, Quality assurance, Acceptance (approval), Surveillance (approval), Quality assurance systems
BS 6001-2:1993
Sampling procedures for inspection by attributes. Specification for sampling plans indexed by limiting quality (LQ) for isolated lot inspection
0 580 21906 2
Summary: Plans that can be used when the switching rules of BS 6001-1 are not applied, e.g. for "isolated lots". Preferred series of limiting qualities (LQ) with consumer's risk usually below 10%. Rationalizes the "ad hoc" procedure mentioned in 11.6 of BS 6001-1.
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Sampling tables, Inspection, Quality control, Quality assurance, Statistical quality control
BS 6001-3:2005
Sampling procedures for inspection by attributes. Specification for skip-lot sampling procedures
0 580 46214 5
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Skip-lot sampling, Inspection, Quality control, Statistical quality control, Frequencies, Sampling tables, Quality assurance, Selection, Size
BS 6001-4:2005
Sampling procedures for inspection by attributes. System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
0 580 46463 6
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Sampling tables, Sequential sampling, Statistical quality control, Inspection, Quality control, Quality assurance, Mathematical calculations
BS 6001-5:2002
Sampling procedures for inspection by attributes. Procedures for assessment of declared quality levels
0 580 40648 2
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Sampling tables, Sequential sampling, Statistical quality control, Acceptance (approval), Quality control, Quality assurance, Conformity, Errors, Probability calculations
BS 6001-7:2006
Acceptance sampling procedures for inspection by attributes. Accept-zero sampling system based on credit principle for controlling outgoing quality
0 580 47773 8
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Quality control, Quality assurance, Acceptance (approval), Batch testing, Conformity, Non-destructive testing, Statistical quality control, Statistical methods of analysis
BS 6001-9:2002
Sampling procedures for inspection by attributes. Double sampling plans using minimal sample sizes, indexed by producer's risk quality (PRQ) and consumer's risk quality (CRQ)
0 580 38991 X
Keywords: Inspection by attributes, Acceptance inspection, Samples, Sampling methods, Quality control, Quality assurance, Acceptance (approval), Surveillance (approval), Quality assurance systems, Sequential sampling, Sampling tables, Statistical quality control, Probability calculations
BS 6002-1:2007
Sampling procedures for inspection by variables. Guide to single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
978 0 580 50163 0
Keywords: Inspection by variables, Inspection, Quality assurance, Acceptance inspection, Sampling tables, Sampling methods, Quality control, Statistical quality control, Standard deviation, Normal distribution, Power spectra, Mathematical calculations, Control charts
BS 6002-2:2007
Sampling procedures for inspection by variables. General guide to single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
978 0 580 50164 7
Keywords: Inspection by variables, Inspection, Quality assurance, Acceptance inspection, Sampling tables, Sampling methods, Quality control, Statistical quality control, Standard deviation, Normal distribution, Power spectra, Mathematical calculations, Control charts
BS 6002-3:2005
Sampling procedures for inspection by variables. Guide to double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
0 580 45424 X
Keywords: Inspection by variables, Inspection, Quality assurance, Acceptance inspection, Sampling tables, Sampling methods, Double, Quality control, Statistical quality control
BS 6002-4:2006
Sampling procedures for inspection by variables. Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
0 580 48593 5
Keywords: Inspection by variables, Inspection, Sequential sampling, Statistical quality control, Quality control, Control charts, Mathematical calculations, Sampling tables, Acceptance inspection, Sampling methods, Assessed quality, Normal distribution, Standard deviation, Statistical distribution, Measurement characteristics
BS 6065:1981
Methods for sampling and acceptance testing of shaped refractory products
0 580 11861 4
Summary: Details methods for sampling products and for obtaining from a sample of the smallest possible size the most precise assessment possible of the quality of a consignment. See also BS 6434.
Keywords: Shaped refractories, Refractories, Ceramics, Sampling methods, Sequential sampling, Acceptance inspection, Inspection, Inspection by attributes, Inspection by variables, Sampling tables, Visual inspection (testing), Defects, Dimensions, Mean, Standard deviation, Power spectra, Mathematical calculations, t-test, Bibliography
BS 6434:1984
Guide to the use of BS 6065 'Methods for sampling and acceptance testing of shaped refractory products'
0 580 13582 9
Summary: Expands on the instructions and provides a number of examples to clarify the method of sampling inspection in BS 6065/ISO 5022.
Keywords: Shaped refractories, Refractories, Ceramics, Sampling methods, Sequential sampling, Acceptance inspection, Inspection, Sampling tables, Specifications, Inspection by attributes, Inspection by variables, Standard deviation, Mean
BS 65:1991
Specification for vitrified clay pipes, fittings and ducts, also flexible mechanical joints for use solely with surface water pipes and fittings
0 580 20268 2
Summary: Specifies certain dimensions, physical and performance characteristics for vitrified clay pipes and fittings. For use in the construction of drainage and sewerage systems, operated as gravity pipelines, or as ducts. Requirements for sampling and marking are also given.
Keywords: Ceramics, Pipes, Pipe fittings, Pipe couplings, Pipe junctions, Bend couplings, Fluid equipment, Ducting, Sealing rings, Drainpipes, Sewers, Drainage, Surface-water drainage, Glazed ceramic ware, Dimensions, Dimensional tolerances, Diameter, Preferred sizes, Perforations, Straightness measurement, Performance, Compressive strength, Crushing tests, Bend testing, Leak tests, Chemical-resistance tests, Water absorption, Acid-resistance tests, Deflection tests, Shear testing, Statistical quality control, Sampling methods, Testing conditions, Marking, Pressure testing, Mechanical testing, Acceptance inspection, Test equipment, Strength of materials, Spigot-and-socket joints
BS 6587:1985
Method of acceptance inspection for fasteners
0 580 14387 2
Summary: Establishes methods of acceptance inspection based on BS 6001 to be used in order to decide whether a lot of fasteners may be accepted or rejected when no other acceptance procedure has been agreed at the time of ordering. The procedure may also be applied when conformance to specification is disputed.
Keywords: Fasteners, Inspection, Acceptance inspection, Acceptance (approval), Dimensions, Mechanical properties of materials, Threaded fasteners, Sampling methods
BS 6699:1992
Specification for ground granulated blastfurnace slag for use with Portland cement
0 580 20456 1
Summary: Manufacture, fineness, glass content, chemical composition, moisture content and, when used with cement, strength, setting time and soundness. Tests for glass content and moisture content.
Keywords: Blast-furnace slag aggregates, Particulate materials, Synthetic aggregates, Aggregates, Portland cement, Blast-furnace cement, Slags, Composition, Fineness, Compressive strength, Chemical composition, Safety measures, Moisture, Statistical quality control, Conformity, Sampling methods, Defects, Marking, Acceptance inspection, Storage, Certification (approval), Determination of content, Glass, Microscopic analysis, Testing conditions, X-ray diffraction analysis, Water content determination
BS 6873:1988
Specification for filament lamps for cycles
0 580 16114 5
Summary: Lamps for cycle headlamps and rear lamps operating at up to 6 V. Methods of test and conditions of compliance to ensure quality and interchangeability.
Keywords: Lamps, Electric lamps, Cycle and motorcycle components, Filament lamps, Vehicle lights, Tail lights, Headlamps, Road vehicle components, Lamp caps, Marking, Cycles, Designations, Sampling methods, Testing conditions, Mechanical testing, Dimensions, Torque, Soldering, Electric power (wattage), Power measurement (electric), Ratings, Design, Rated voltage, Rated current, Luminous flux, Inspection, Optical measurement, Life (durability), Statistical quality control, Endurance testing, Conformity, Acceptance inspection
BS 7315:1990+A1:1993
Specification for wrought aluminium and aluminium alloy enclosures for gas-filled high-voltage switchgear and controlgear
978 0 580 60722 6
Summary: Requirements for fusion welded enclosures pressurized with dry air, inert gas used in indoor or outdoor installations with rated voltages of 72.5 kV and above.
Keywords: Wrought alloys, Aluminium, Aluminium alloys, Switchgear, High-voltage equipment, Electric enclosures, Electric control equipment, Welding, Design, Flanges, Welded joints, Marking, Pressure testing, Stress analysis, Non-destructive testing, Electrical equipment, Protected electrical equipment, Electrical insulation devices, Rated voltage, Gases, Insulating enclosures, Shell structures, Thickness, Design calculations, Holes, Assembling, Form tolerances, Dimensional tolerances, Acceptance inspection, Approval testing, Certification (approval), Elastic design, Enclosures
EN 50064:1989+A1:1993
Specification for wrought aluminium and aluminium alloy enclosures for gas-filled high-voltage switchgear and controlgear
978 0 580 60722 6
Summary: Requirements for fusion welded enclosures pressurized with dry air, inert gas used in indoor or outdoor installations with rated voltages of 72.5 kV and above.
Keywords: Wrought alloys, Aluminium, Aluminium alloys, Switchgear, High-voltage equipment, Electric enclosures, Electric control equipment, Welding, Design, Flanges, Welded joints, Marking, Pressure testing, Stress analysis, Non-destructive testing, Electrical equipment, Protected electrical equipment, Electrical insulation devices, Rated voltage, Gases, Insulating enclosures, Shell structures, Thickness, Design calculations, Holes, Assembling, Form tolerances, Dimensional tolerances, Acceptance inspection, Approval testing, Certification (approval), Elastic design, Enclosures
BS 7339:1990
Code of practice for supplementary checking of metallic materials of construction in pressurized systems
0 580 18749 7
Summary: The techniques and methods supplement traditional methods of material identification like hard stamping. They are intended to increase confidence level in materials actually meeting specification.
Keywords: Metals, Pressure equipment, Pressurization, Pressure vessels, Pipework systems, Fluid equipment, Inspection, Quality assurance, Acceptance (approval), Acceptance inspection, Certification (approval), Pressure pipes, Alloys, Non-destructive testing
BS 7783:1994
Acceptance control charts
0 580 23475 4
Keywords: Control charts, Inspection, Quality assurance, Acceptance inspection, Acceptance (approval), Statistical quality control, Quality control, Process control, Sampling methods, Statistical methods of analysis, Mathematical calculations
BS 903-2:1997
Physical testing of rubber. Guide to the application of statistics to rubber testing
0 580 25400 3
Summary: It is intended not to conflict with or replace existing British standards covering basic statistical techniques, but rather to complement them and provide examples of those techniques applied to particular rubber testing situations.
Keywords: Natural rubber, Synthetic rubber, Ageing tests, Tensile testing, Compression testing, Tear tests, Hardness testing, Fatigue testing, Wear resistance, Tensile strength, Statistics, Statistical methods of analysis, Statistical testing, Statistical data, Statistical distribution, Average, Mean, Median (statistics), Statistical dispersion, Normal distribution, Exponential distribution, Standard deviation, Range (statistics), Coefficient of variation, Analysis of variance, Experimental design, Factorial experiments, Regression analysis, Estimation, Interpolation, Extrapolation, Confidence limits, Sampling methods, Inspection by attributes, Inspection by variables, Inspection, Acceptance inspection, Comparative tests, Rounding (numbers), Arithmetic operations, Mathematical operations, Paired comparison tests, Statistical quality control, Control charts, Cusum charts, Probability theory
BS A 101:1969
Specification for general requirements for titanium bolts
0 580 05359 8
Keywords: Bolts, External-thread fasteners, Titanium alloys, Aircraft components, Air transport engineering, Threaded fasteners, Threaded components, Fasteners, Marking, Inspection, Acceptance inspection, Statistical quality control, Surface texture, Dimensional tolerances, Defects, Surface defects, Size, Performance testing, Heat treatment, Tensile testing, Shear testing, Fatigue testing, Test equipment, Dimensions, Metallography, Crystal microstructure, Threads, Incomplete threads, Shear strength, Tensile strength, Designations
BS A 300:1989
Specification for procurement of alloy steel bolts with strength classification 1 100 MPa and MJ threads
0 580 17459 X
Summary: Characteristics and quality assurance requirements for bolts with normal heads intended for use in aerospace construction.
Keywords: Bolts, External-thread fasteners, Threaded fasteners, Fasteners, Alloy steels, Steels, Aircraft components, Sampling methods, Approval testing, Acceptance inspection, Testing conditions, Hardness, Defects, Shear strength, Quality control, Statistical quality control, Qualification approval, Grades (quality), Tensile strength, Marking, Quality assurance, MJ threads, Space technology components
BS A 351:2000
Rivets, solid, in nickel alloy. Procurement specification
0 580 34619 6
Keywords: Aircraft components, Rivets, Threadless fasteners, Fasteners, Nickel alloys, Purchasing, Quality assurance, Acceptance (approval), Approval testing, Acceptance inspection, Statistical quality control, Defects, Classification systems, Shear strength, Sampling tables, Ordering
BS A 352:2000
Rivets, solid, in titanium or titanium alloy. Procurement specification
0 580 34617 X
Keywords: Aircraft components, Rivets, Threadless fasteners, Titanium, Titanium alloys, Purchasing, Ordering, Quality assurance, Acceptance inspection, Specification (approval), Shear strength, Sampling methods, Sampling tables
BS A 363:2000
Bolts, with MJ threads, made of heat-resistant nickel-based alloy, strength class 1 550 MPa. Procurement specification
0 580 34473 8
Keywords: Bolts, External-thread fasteners, MJ threads, Heat-resistant materials, Nickel alloys, Strength of materials, Aircraft components, Quality assurance, Quality assurance systems, Acceptance (approval), Acceptance inspection, Statistical quality control, Production processes, Hot-working, Heat treatment, Contaminants, Fillets (shape), Threads, Surface properties, Passivation, Mechanical properties of materials, Tensile strength, Temperature, Shear strength, Hardness, Torque, Corrosion, Packaging, Labelling (process), Certificates of conformity, Defects, Tolerances (measurement), Sampling methods, Dimensional tolerances, Tensile testing
BS EN 10228-2:1998
Non-destructive testing of steel forgings. Penetrant testing
0 580 29795 0
Keywords: Steels, Forgings, Non-destructive testing, Penetrant flaw detection, Flaw detection, Surface defects, Defects, Surface treatment, Grades (quality), Visual inspection (testing), Acceptance inspection, Classification systems, Testing conditions, Technical documents, Consumer-supplier relations
BS EN 10246-3:2000
Non-destructive testing of steel tubes. Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
0 580 35434 2
Keywords: Non-destructive testing, Steels, Pipes, Seamless pipes, Welding, Flaw detection, Automatic, Eddy-current tests, Calibration, Acceptance inspection, Approval testing
BS EN 10246-4:2000
Non-destructive testing of steel tubes. Automatic full peripheral magnetic transducer/flux leakage testing of seamless ferromagnetic steel tubes for the detection of transverse imperfections
0 580 35435 0
Keywords: Non-destructive testing, Steels, Pipes, Seamless pipes, Automatic, Transducers, Magnetic-particle flaw detection, Leak tests, Transverse, Flaw detection, Diameter, Control samples, Designations, Calibration, Acceptance inspection
BS EN 10246-5:2000
Non-destructive testing of steel tubes. Automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal imperfections
0 580 35436 9
Keywords: Non-destructive testing, Steels, Pipes, Automatic, Seamless pipes, Seamed pipes, Diameter, Flaw detection, Magnetic flux density, Magnetic measurement, Leak tests, Transducers, Designations, Thickness, Acceptance (approval), Acceptance inspection, Calibration, Control samples, Test equipment
BS EN 10304:2001
Magnetic materials (iron and steel) for use in relays
0 580 37000 3
Keywords: Magnetic materials, Iron, Steels, Relays, Semi-finished products, Wires, Surface treatment, Thickness, Dimensional tolerances, Straightness measurement, Acceptance inspection
BS EN 12062:1998
Non-destructive examination of welds. General rules for metallic materials
0 580 28699 1
Keywords: Welding, Welded joints, Joints, Examination (quality assurance), Non-destructive testing, Metals, Quality control, Thickness, Acceptance inspection, Acceptance (approval), Defects, Steels, Aluminium, Copper, Nickel, Titanium, Nickel alloys, Copper alloys, Technical documents, Selection, Sampling methods, Visual inspection (testing), Penetrant flaw detection, Eddy-current tests, Magnetic-particle flaw detection, Radiographic testing, Ultrasonic testing, Classification systems
BS EN 122150:1996
Harmonized system of quality assessment for electronic components. Sectional specification: radio frequency coaxial connectors. Series EIA Flange
0 580 26233 2
Summary: Provides information and rules for the preparation of detail specifications for the series of EIA Flange coaxial connectors.
Keywords: Electric connectors, Electrical components, Coaxial connectors, Radiofrequencies, Flanged fittings, Detail specification, Dimensions, Designations, Electrical testing, Environmental testing, Performance, Reflection factor, Contact resistance, Electrical resistance, Electrical insulation, Electrical impedance, Voltage, Tensile strength, Environment (working), Testing conditions, Endurance testing, Thermal testing, Acceptance inspection, Quality assurance systems, Quality control, Electronic equipment and components, Dimensional tolerances, Flanges, Ratings, Mechanical testing, Electrical properties of materials, Approval testing, Qualification approval, Specification (approval), Statistical quality control
BS EN 122190:1996
Harmonized system of quality assessment for electronic components. Sectional specification: radio frequency coaxial connectors. Series 7-16
0 580 26104 2
Summary: Provides information and rules for the preparation of detail specifications for screw coupled coaxial connectors series 7-16.
Keywords: Electric connectors, Electrical components, Coaxial connectors, Radiofrequencies, Detail specification, Dimensions, Designations, Electrical testing, Environmental testing, Performance, Reflection factor, Contact resistance, Electrical resistance, Electrical insulation, Electrical impedance, Voltage, Tensile strength, Environment (working), Testing conditions, Endurance testing, Thermal testing, Acceptance inspection, Quality assurance systems, Quality control, Electronic equipment and components, Dimensional tolerances, Ratings, Mechanical testing, Electrical properties of materials, Approval testing, Qualification approval, Specification (approval), Statistical quality control
BS EN 12467:2004
Fibre-cement flat sheets. Product specification and test methods
0 580 45048 1
Keywords: Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspection, Construction materials
BS EN 1289:1998
Non-destructive examination of welds. Penetrant testing of welds. Acceptance levels
0 580 29631 8
Keywords: Non-destructive testing, Penetrant flaw detection, Flaw detection, Welded joints, Welding, Surface defects, Defects, Inspection, Acceptance inspection, Acceptance (approval), Grades (quality)
BS EN 1291:1998
Non-destructive testing of welds. Magnetic particle testing of welds. Acceptance levels
0 580 29629 6
Keywords: Welded joints, Welding, Non-destructive testing, Steels, Magnetic-particle flaw detection, Flaw detection, Examination (quality assurance), Inspection, Acceptance inspection, Surface properties, Surface defects
BS EN 12952-15:2003
Water-tube boilers and auxiliary installations. Acceptance tests
0 580 42757 9
Keywords: Water-tube boilers, Steam boilers, Boilers, Auxiliary, Heating equipment, Heaters, Fired pressure vessels, Hot-water boilers, Water heaters, Heat engineering components, Steam, Pressure measurement (fluids), Approval testing, Acceptance inspection, Inspection, Performance testing, Performance, Thermal output, Thermal efficiency
BS EN 12953-5:2002
Shell boilers. Inspection during construction, documentation and marking of pressure parts of the boiler
0 580 39849 8
Keywords: Fire-tube boilers, Boilers, Steam boilers, Hot-water boilers, Visual inspection (testing), Inspection, Non-destructive testing, Welded joints, Acceptance (approval), Acceptance inspection, Assembling, Quality control, Destructive testing, Pressure testing, Personnel, Technical documents, Marking, Conformity
BS EN 13002-2:1999
Carbon fibre yarns. Test methods and general specifications
0 580 32547 4
Keywords: Carbon fibres, Man-made fibres, Yarn, Reinforcing materials, Modulus of elasticity, Performance testing, Approval testing, Acceptance inspection, Inspection, Physical properties of materials, Contamination, Defects, Sampling methods, Acceptance (approval), Certificates of conformity, Marking, Storage, Packaging
BS EN 13231-1:2006
Railway applications. Track. Acceptance of works. Works on ballasted track. Plain line
0 580 48621 4
Keywords: Railway track, Railway fixed equipment, Railway equipment, Service contracts, Consumer-supplier relations, Acceptance inspection, Acceptance (approval), Plain track, Ballast (aggregates), Dimensional tolerances, Railway applications
BS EN 13231-2:2006
Railway applications. Track. Acceptance of works. Works on ballasted track. Switches and crossings
0 580 48622 2
Keywords: Railway track, Railway fixed equipment, Railway equipment, Service contracts, Consumer-supplier relations, Acceptance inspection, Acceptance (approval), Ballast (aggregates), Dimensional tolerances, Turnouts, Point work, Railway applications
BS EN 13232-9:2006
Railway applications. Track. Switches and crossings. Layouts
0 580 48606 0
Keywords: Railway track, Railway rails, Switches, Turnouts, Layout, Design, Safety measures, Dimensions, Approval testing, Verification, Acceptance inspection, Railway fixed equipment, Railway applications
BS EN 1371-1:1997
Founding. Liquid penetrant inspection. Sand, gravity die and low pressure die castings
0 580 28601 0